From 7727abd30b3689e682f9c39848000970e50c1d83 Mon Sep 17 00:00:00 2001
From: Sgr A* VMT <1611902585@qq.com>
Date: Tue, 30 Jan 2024 21:00:13 +0800
Subject: [PATCH] remove file

---
 说明.txt | 87 --------------------------------------------------------
 1 file changed, 87 deletions(-)
 delete mode 100644 说明.txt

diff --git a/说明.txt b/说明.txt
deleted file mode 100644
index 68c7d6b..0000000
--- a/说明.txt
+++ /dev/null
@@ -1,87 +0,0 @@
-为了保证精度，请安装时尽可能让传感器线圈板的顶面低于加热块的底面。
-
-在用户目录下执行git clone https://gitee.com/NBTP/IDM.git 下载程序包
-
-执行chmod +x IDM/install.sh
-然后执行IDM/install.sh进行安装
-这一步会自动把脚本创建一个链接放到klipper/klipper/extra目录下
-然后
-[idm]
-serial:
-#canbus_uuid:
-#   Path to the serial port for the idm device. Typically has the form
-#   /dev/serial/by-id/usb-idm_idm_...
-speed: 40.
-#   Z probing dive speed.
-lift_speed: 5.
-#   Z probing lift speed.
-backlash_comp: 0.5
-#   Backlash compensation distance for removing Z backlash before measuring
-#   the sensor response.
-x_offset: 0.
-#   X offset of idm from the nozzle.
-y_offset: 21.1
-#   Y offset of idm from the nozzle.
-trigger_distance: 2.
-#   idm trigger distance for homing.
-trigger_dive_threshold: 1.5
-#   Threshold for range vs dive mode probing. Beyond `trigger_distance +
-#   trigger_dive_threshold` a dive will be used.
-trigger_hysteresis: 0.006
-#   Hysteresis on trigger threshold for untriggering, as a percentage of the
-#   trigger threshold.
-cal_nozzle_z: 0.1
-#   Expected nozzle offset after completing manual Z offset calibration.
-cal_floor: 0.1
-#   Minimum z bound on sensor response measurement.
-cal_ceil:5.
-#   Maximum z bound on sensor response measurement.
-cal_speed: 1.0
-#   Speed while measuring response curve.
-cal_move_speed: 10.
-#   Speed while moving to position for response curve measurement.
-default_model_name: default
-#   Name of default idm model to load.
-mesh_main_direction: x
-#   Primary travel direction during mesh measurement.
-#mesh_overscan: -1
-#   Distance to use for direction changes at mesh line ends. Omit this setting
-#   and a default will be calculated from line spacing and available travel.
-mesh_cluster_size: 1
-#   Radius of mesh grid point clusters.
-mesh_runs: 2
-#   Number of passes to make during mesh scan.
-请注意调整配置中的x y方向偏移。确保校准过程中喷头会将线圈移动到原先喷嘴所在xy位置。
-将这段配置放进printer.cfg并将serial修改为你查询到的idm的串口号
-can版本的话使用常规的查询方法搜索can的uuid并填入
-在配置里再加入
-[force_move]
-enable_force_move: true
-方便校准，校准全部结束后可删除
-
-之后把[probe]模块删除
-并将z限位修改为probe:z_virtual_endstop
-还需要设置
-[safe_z_home]
-home_xy_position: 【你的x轴中心坐标】,【你的y轴中心坐标】
-z_hop: 10
-记得设置[bed_mesh]不然会报错
-
-重启之后将热端移动到中间并徒手将喷嘴贴到平台上
-输入SET_KINEMATIC_POSITION x=【平台中心x坐标】 y=【平台中心y轴坐标】 z=0
-之后执行idm_calibrate的指令
-点击-0.1的偏移后确认，会自动进行校准
-在控制台输入idm并按tab键可以看到所有支持的指令
-
-将z_tilt或者quad_gantry_level中的horizontal_z_move降到trigger_distance + trigger_dive_threshold以下(默认为3)可以使调平进入高速模式，觉得太低可以适当拉高trigger_dive_threshold使horizontal_z_move可以拉高一些。
-
-
-含加速计(lis2dw)的版本可以在配置中添加以下内容启用加速计:
-[lis2dw]
-cs_pin: idm:PA3
-spi_bus: spi1
-
-[resonance_tester]
-accel_chip: lis2dw
-probe_points:
-    125, 125, 20  #此处设置为你进行共振测量时喷头所处坐标