88 lines
3.3 KiB
Plaintext
88 lines
3.3 KiB
Plaintext
为了保证精度，请安装时尽可能让传感器线圈板的顶面低于加热块的底面。
|
||
|
||
在用户目录下执行git clone https://gitee.com/NBTP/IDM.git 下载程序包
|
||
|
||
执行chmod +x IDM/install.sh
|
||
然后执行IDM/install.sh进行安装
|
||
这一步会自动把脚本创建一个链接放到klipper/klipper/extra目录下
|
||
然后
|
||
[idm]
|
||
serial:
|
||
#canbus_uuid:
|
||
# Path to the serial port for the idm device. Typically has the form
|
||
# /dev/serial/by-id/usb-idm_idm_...
|
||
speed: 40.
|
||
# Z probing dive speed.
|
||
lift_speed: 5.
|
||
# Z probing lift speed.
|
||
backlash_comp: 0.5
|
||
# Backlash compensation distance for removing Z backlash before measuring
|
||
# the sensor response.
|
||
x_offset: 0.
|
||
# X offset of idm from the nozzle.
|
||
y_offset: 21.1
|
||
# Y offset of idm from the nozzle.
|
||
trigger_distance: 2.
|
||
# idm trigger distance for homing.
|
||
trigger_dive_threshold: 1.5
|
||
# Threshold for range vs dive mode probing. Beyond `trigger_distance +
|
||
# trigger_dive_threshold` a dive will be used.
|
||
trigger_hysteresis: 0.006
|
||
# Hysteresis on trigger threshold for untriggering, as a percentage of the
|
||
# trigger threshold.
|
||
cal_nozzle_z: 0.1
|
||
# Expected nozzle offset after completing manual Z offset calibration.
|
||
cal_floor: 0.1
|
||
# Minimum z bound on sensor response measurement.
|
||
cal_ceil:5.
|
||
# Maximum z bound on sensor response measurement.
|
||
cal_speed: 1.0
|
||
# Speed while measuring response curve.
|
||
cal_move_speed: 10.
|
||
# Speed while moving to position for response curve measurement.
|
||
default_model_name: default
|
||
# Name of default idm model to load.
|
||
mesh_main_direction: x
|
||
# Primary travel direction during mesh measurement.
|
||
#mesh_overscan: -1
|
||
# Distance to use for direction changes at mesh line ends. Omit this setting
|
||
# and a default will be calculated from line spacing and available travel.
|
||
mesh_cluster_size: 1
|
||
# Radius of mesh grid point clusters.
|
||
mesh_runs: 2
|
||
# Number of passes to make during mesh scan.
|
||
请注意调整配置中的x y方向偏移。确保校准过程中喷头会将线圈移动到原先喷嘴所在xy位置。
|
||
将这段配置放进printer.cfg并将serial修改为你查询到的idm的串口号
|
||
can版本的话使用常规的查询方法搜索can的uuid并填入
|
||
在配置里再加入
|
||
[force_move]
|
||
enable_force_move: true
|
||
方便校准，校准全部结束后可删除
|
||
|
||
之后把[probe]模块删除
|
||
并将z限位修改为probe:z_virtual_endstop
|
||
还需要设置
|
||
[safe_z_home]
|
||
home_xy_position: 【你的x轴中心坐标】,【你的y轴中心坐标】
|
||
z_hop: 10
|
||
记得设置[bed_mesh]不然会报错
|
||
|
||
重启之后将热端移动到中间并徒手将喷嘴贴到平台上
|
||
输入SET_KINEMATIC_POSITION x=【平台中心x坐标】 y=【平台中心y轴坐标】 z=0
|
||
之后执行idm_calibrate的指令
|
||
点击-0.1的偏移后确认，会自动进行校准
|
||
在控制台输入idm并按tab键可以看到所有支持的指令
|
||
|
||
将z_tilt或者quad_gantry_level中的horizontal_z_move降到trigger_distance + trigger_dive_threshold以下(默认为3)可以使调平进入高速模式，觉得太低可以适当拉高trigger_dive_threshold使horizontal_z_move可以拉高一些。
|
||
|
||
|
||
含加速计(lis2dw)的版本可以在配置中添加以下内容启用加速计:
|
||
[lis2dw]
|
||
cs_pin: idm:PA3
|
||
spi_bus: spi1
|
||
|
||
[resonance_tester]
|
||
accel_chip: lis2dw
|
||
probe_points:
|
||
125, 125, 20 #此处设置为你进行共振测量时喷头所处坐标
|