добавлена щетка, смещение тача, переписан авд, праймлайн на тпу
This commit is contained in:
322
addon/OrbiterSensor.cfg
Normal file
322
addon/OrbiterSensor.cfg
Normal file
@@ -0,0 +1,322 @@
|
||||
#################################################################################################################
|
||||
################################# Orbiter Sensor CONFIGURATION ##################################################
|
||||
#################################################################################################################
|
||||
|
||||
#config file version v2.2.04
|
||||
#release date: 23.09.2023
|
||||
|
||||
# PAUSE and RESUME macros are defined at the end of this config file.
|
||||
# If you prefer using your own p[lease delete them, otherwise define parking position below.
|
||||
|
||||
#################################################################################################################
|
||||
################################# CHANGE HERE MACRO CONFIGURABLES################################################
|
||||
#################################################################################################################
|
||||
|
||||
[gcode_macro _SENSOR_VARIABLES] # change here macro configurables, enable disable functions!*************************
|
||||
variable_filament_load_temp :230 # temperature to heat up hotend for filament loading, default is 235
|
||||
variable_filament_unload_temp :200 # temperature to heat up hotend for filament un-loading, default is 185
|
||||
variable_filament_load_min_temp :200 # minimum hotend set temperature allowed in filament load macro, default is 190
|
||||
variable_nozzle_purge_length :160 # filament extrude amount during load sequenc, hotend purge from old filament, default is 200
|
||||
variable_nozzle_purge_speed :450 # filament extrude speed in mm/min adjust this value lower if flow is too high and extruder skips during loading, default is 300
|
||||
variable_unload_distance :120 # filament retract distance for unload procedure. this length shall be long enough to extract the filament above the drive gears
|
||||
variable_disable_autoload :False # disable filament autoload feature by setting this variable True
|
||||
variable_disable_runnout :False # disable runnout by setting this variable True
|
||||
variable_disable_autounload :False # disable auto unload filament by setting this variable to True
|
||||
variable_enable_beep :True # uses M300 sound feature, set it True to enable
|
||||
variable_park_position_x :10 # edit your X parking position here for pause macro trigerred by runnout
|
||||
variable_park_position_y :10 # edit your Y parking position here for pause macro trigerred by runnout
|
||||
variable_park_lift_z :10 # edit your Z lift amount for parking position here, default is 10
|
||||
Variable_park_retraction :1 # edit your retraction amount for parking, default is 1
|
||||
gcode:
|
||||
|
||||
#///////////////////////////filament sensor button macros/////////////////////////////////////////////////
|
||||
[gcode_button filament_sense]
|
||||
pin: !toolboard: PB5 # remove the negation "!" for sensor v1 - use just PA9 as example
|
||||
press_gcode: # sensor released -runnout detected!
|
||||
runnout_init
|
||||
release_gcode: #gcode macro for filament auto-load, sensor pressed
|
||||
filament_load_init
|
||||
#********************************************************************************************************
|
||||
|
||||
#////////////////////////////////////////Filament Unload macros/////////////////////////////////////////////////
|
||||
[gcode_button filament_unload]
|
||||
pin: !toolboard: PB7 # remove the negation "!" for sensor v1 - use just PA9 as example
|
||||
release_gcode: # filament unload procedure
|
||||
filament_unload_init
|
||||
press_gcode: # do not add any macro call here
|
||||
|
||||
#################################################################################################################################
|
||||
####################################### DO NOT CHANGE ANYTHING BELOW THIS LINE!!! ###############################################
|
||||
#################################################################################################################################
|
||||
####################################### UNLESS YOU KNOW WHAT YOU ARE DOING OR YOU ARE BORED AND NEED TO DO SOMETHING OR YOU ARE ALONE AND NEED SOMETHING TO MESS UP YOUR LIFE OR YOU CAN DO IT BETTER THAN ME OR YOU ARE A REAL SMARTASS OR JUST BECAUSE YOU CAN OR YOU RUN OUT OF BEAR OR HAS NOTHING BETTER TO DO OR ANY UNREASONABLE REASON
|
||||
#################################################################################################################################
|
||||
|
||||
[respond]
|
||||
default_type: echo
|
||||
|
||||
[force_move]
|
||||
enable_force_move: True
|
||||
|
||||
[gcode_macro runnout_init]
|
||||
gcode:
|
||||
{% set sensor = printer['gcode_macro _SENSOR_VARIABLES'] %}
|
||||
{% if (printer.print_stats.state == "printing") %}
|
||||
{% if(sensor.disable_runnout|lower == 'false') %}
|
||||
filament_change_state1
|
||||
{% else %}
|
||||
M118 Filament runnout is disabled in the sensor config file!
|
||||
{% endif %}
|
||||
{% endif %}
|
||||
UPDATE_DELAYED_GCODE ID=clear_loadbusy DURATION=2
|
||||
UPDATE_DELAYED_GCODE ID=clear_unloadbusy DURATION=2
|
||||
SET_GCODE_VARIABLE MACRO=filament_unload VARIABLE=filamentpresent VALUE=0
|
||||
|
||||
[gcode_macro filament_change_state1]
|
||||
variable_changebusy: 0
|
||||
variable_temp_target: 0
|
||||
gcode:
|
||||
{% set sensor = printer['gcode_macro _SENSOR_VARIABLES'] %}
|
||||
{% if changebusy == 0 %}
|
||||
PAUSE # call printer pause macro
|
||||
SET_GCODE_VARIABLE MACRO=filament_change_state1 VARIABLE=changebusy VALUE=1
|
||||
M118 Filament runnout!
|
||||
filament_change_state2 # comment this line if you do not want to automatically unload filament in case there is a runnout detected.
|
||||
{% else %}
|
||||
{% endif %}
|
||||
|
||||
[gcode_macro filament_change_state2]
|
||||
gcode:
|
||||
{% set sensor = printer['gcode_macro _SENSOR_VARIABLES'] %}
|
||||
SET_GCODE_VARIABLE MACRO=filament_load VARIABLE=loadbusy VALUE=1
|
||||
{% if (sensor.enable_beep|lower == 'true') %}
|
||||
M300 # beep sound
|
||||
{% endif %}
|
||||
M118 Unloading filament...
|
||||
M83
|
||||
G92 E0
|
||||
# {% if printer[printer.toolhead.extruder].temperature < 185 %} # hardcoded threshold
|
||||
{% if (printer.extruder.can_extrude|lower != 'true')%} # checing for minimum extrusion temperature
|
||||
# check if temperature is over the minimum extrusion temp. min_extrude_temp must be defined in the extruder config (to about 185)
|
||||
M118 Hotend heating!
|
||||
SET_HEATER_TEMPERATURE HEATER=extruder TARGET={sensor.filament_unload_temp} # restore user temp if it was set before loading
|
||||
TEMPERATURE_WAIT SENSOR=extruder MINIMUM={sensor.filament_unload_temp} #wait for reaching filament unload temp
|
||||
{% endif %}
|
||||
{% if(printer.extruder.target == 0) %} # checing for set temperature if is zero than set to 200 / hotend hot but cooling due to set target temp 0
|
||||
SET_HEATER_TEMPERATURE HEATER=extruder TARGET={sensor.filament_unload_temp} # restore user temp if it was set before loading
|
||||
TEMPERATURE_WAIT SENSOR=extruder MINIMUM={sensor.filament_unload_temp} #wait for reaching filament unload temp
|
||||
{% endif %}
|
||||
G0 E-5 F3600 #extract filament to cold end
|
||||
G4 P2000 # wait for two seconds
|
||||
G0 E5 F3600 # push the filament back
|
||||
G0 E-5 F3600 #extract filament to cold end
|
||||
G0 E-{sensor.unload_distance} F300 # continue extraction slow allow filament to be cooled enough before reaches the gears
|
||||
M400
|
||||
M118 Load new filament! Wait until is loaded, then resume printing.
|
||||
SET_HEATER_TEMPERATURE HEATER=extruder TARGET=0 # swicth off heater
|
||||
UPDATE_DELAYED_GCODE ID=clear_loadbusy DURATION=2.5 # timing must be set to clear delay plus 0.5s. is due to wait to remove filament before starting load even in case there is a blob at the tip of the extracted filament which woudl trigger the sensor twice
|
||||
|
||||
#############################################END filament auto load macro section END***********************************************************
|
||||
|
||||
[gcode_macro filament_load_init]
|
||||
gcode:
|
||||
{% set sensor = printer['gcode_macro _SENSOR_VARIABLES'] %}
|
||||
{% if (printer.print_stats.state != "printing") %}
|
||||
{% if(sensor.disable_autoload|lower == 'false') %}
|
||||
filament_load
|
||||
{% else %}
|
||||
M118 Filament auto-load is disabled in the sensor config file!
|
||||
{% endif %}
|
||||
{% else %}
|
||||
M118 Printing! Can't load filament right now!
|
||||
{% endif %}
|
||||
SET_GCODE_VARIABLE MACRO=filament_unload VARIABLE=filamentpresent VALUE=1
|
||||
UPDATE_DELAYED_GCODE ID=clear_changebusy DURATION=2
|
||||
|
||||
[gcode_macro filament_load]
|
||||
variable_loadbusy: 0
|
||||
variable_USER_TEMP: 0
|
||||
variable_LOAD_TEMP: 0
|
||||
gcode:
|
||||
{% set sensor = printer['gcode_macro _SENSOR_VARIABLES'] %}
|
||||
{% if loadbusy == 0 %} # requires [virtual_sdcard]
|
||||
SET_GCODE_VARIABLE MACRO=filament_load VARIABLE=loadbusy VALUE=1
|
||||
SET_GCODE_VARIABLE MACRO=filament_unload VARIABLE=unloadbusy VALUE=1
|
||||
{% set USER_TEMP = printer.extruder.target %} # save user set temperature before loading
|
||||
{% set LOAD_TEMP = 0 %}
|
||||
#M118 USER TEMP {USER_TEMP} # echo back for debug only
|
||||
{% if (printer.extruder.can_extrude|lower != 'true') or (printer.extruder.target < sensor.filament_load_min_temp) %} # checking for minimum extrusion temperature
|
||||
# check if temperature is over the minimum extrusion temp. min_extrude_temp must be defined in the extruder config (to about 185)
|
||||
SET_HEATER_TEMPERATURE HEATER=extruder TARGET={sensor.filament_load_temp} # set user defined load temperature
|
||||
{% set LOAD_TEMP = sensor.filament_load_temp %} # save user set temperature before loading
|
||||
M118 Hotend heating!
|
||||
{% endif %}
|
||||
{% if (sensor.enable_beep|lower == 'true') %}
|
||||
M300 # beep sound
|
||||
{% endif %}
|
||||
M118 Filament loading!
|
||||
M82 #set extruder to absolute mode
|
||||
G92 E0
|
||||
G4 P1500 # wait for 1.5 seconds
|
||||
FORCE_MOVE STEPPER=extruder DISTANCE=15 VELOCITY=10 ACCEL=1000 # load filament inside the gears force move needs to be enabled
|
||||
TEMPERATURE_WAIT SENSOR=extruder MINIMUM={LOAD_TEMP} # wait for reaching set temperature
|
||||
TEMPERATURE_WAIT SENSOR=extruder MINIMUM={USER_TEMP} # wait for reaching set temperature
|
||||
G1 E{sensor.nozzle_purge_length} F{sensor.nozzle_purge_speed} # extrude preconfigured purge length
|
||||
M400 # wait to complete nozzle purge
|
||||
SET_HEATER_TEMPERATURE HEATER=extruder TARGET={USER_TEMP} # restore user temp if it was set before loading
|
||||
M118 Filament load complete!
|
||||
UPDATE_DELAYED_GCODE ID=clear_unloadbusy DURATION=2
|
||||
{% else %}
|
||||
M118 Filament already loaded!
|
||||
{% endif %}
|
||||
#############################################END filament suto load macro section END***********************************************************
|
||||
#############################################filament auto unload macro section*****************************************************************
|
||||
[gcode_macro filament_unload_init]
|
||||
gcode:
|
||||
{% set sensor = printer['gcode_macro _SENSOR_VARIABLES'] %}
|
||||
{% if (printer.print_stats.state != "printing") %}
|
||||
{% if(sensor.disable_autounload|lower == 'false') %}
|
||||
filament_unload
|
||||
{% else %}
|
||||
M118 Filament auto-unload is disabled in the sensor config file!
|
||||
{% endif %}
|
||||
{% else %}
|
||||
M118 Printing! Can't unload filament right now!
|
||||
{% endif %}
|
||||
|
||||
[gcode_macro filament_unload]
|
||||
variable_unloadbusy: 0
|
||||
variable_filamentpresent: 0
|
||||
gcode:
|
||||
{% set sensor = printer['gcode_macro _SENSOR_VARIABLES'] %}
|
||||
{% if unloadbusy == 0 %} # requires [virtual_sdcard]
|
||||
SET_GCODE_VARIABLE MACRO=filament_unload VARIABLE=unloadbusy VALUE=1
|
||||
SET_GCODE_VARIABLE MACRO=filament_load VARIABLE=loadbusy VALUE=1
|
||||
{% if (sensor.enable_beep|lower == 'true') %}
|
||||
M300 # beep sound
|
||||
{% endif %}
|
||||
M118 Filament unloading!
|
||||
M83
|
||||
G92 E0
|
||||
# {% if (printer.extruder.can_extrude|lower != 'true') or (printer.extruder.target == 0)%} # checing for minimum extrusion temperature
|
||||
{% if (printer.extruder.can_extrude|lower != 'true')%} # checing for minimum extrusion temperature
|
||||
# check if temperature is over the minimum extrusion temp. min_extrude_temp must be defined in the extruder config (to about 185)
|
||||
M118 Hotend heating!
|
||||
SET_HEATER_TEMPERATURE HEATER=extruder TARGET={sensor.filament_unload_temp} # restore user temp if it was set before loading
|
||||
TEMPERATURE_WAIT SENSOR=extruder MINIMUM={sensor.filament_unload_temp} # wait for reaching configured unload temperature
|
||||
{% endif %}
|
||||
{% if(printer.extruder.target == 0) %} # checing for set temperature if is zero than set to 185 / hotend hot but cooling due to set target temp 0
|
||||
TEMPERATURE_WAIT SENSOR=extruder MINIMUM={sensor.filament_unload_temp} # wait for reaching configured unload temperature
|
||||
{% endif %}
|
||||
G0 E10 F500 # extruder 20mm of filament before extracting
|
||||
G0 E-5 F3600 #extract filament to cold end
|
||||
G4 P2000 # wait for two seconds
|
||||
G0 E6 F3600 # push the filament back
|
||||
G0 E-10 F3600 #extract filament to cold end
|
||||
G0 E-{sensor.unload_distance} F300 # continue extraction slow allow filament to be cooled enough before reaches the gears
|
||||
M104 S0 T0
|
||||
M400 # wait to complete unload
|
||||
M118 Filament unload complete!
|
||||
#SET_GCODE_VARIABLE MACRO=filament_load VARIABLE=loadbusy VALUE=0
|
||||
{% else %}
|
||||
M118 Nothing to unload!
|
||||
{% endif %}
|
||||
|
||||
#############################################END filament auto unload macro section END***********************************************************
|
||||
|
||||
[delayed_gcode clear_unloadbusy]
|
||||
gcode:
|
||||
SET_GCODE_VARIABLE MACRO=filament_unload VARIABLE=unloadbusy VALUE=0
|
||||
#M118 Clear Unload busy!
|
||||
|
||||
[delayed_gcode clear_changebusy]
|
||||
gcode:
|
||||
SET_GCODE_VARIABLE MACRO=filament_change_state1 VARIABLE=changebusy VALUE=0
|
||||
#M118 Clear Load busy!
|
||||
|
||||
[delayed_gcode set_loadbusy]
|
||||
gcode:
|
||||
SET_GCODE_VARIABLE MACRO=filament_load VARIABLE=loadbusy VALUE=1
|
||||
#M118 Set Load busy!
|
||||
|
||||
[delayed_gcode clear_loadbusy]
|
||||
gcode:
|
||||
SET_GCODE_VARIABLE MACRO=filament_load VARIABLE=loadbusy VALUE=0
|
||||
#M118 Clear Load busy!
|
||||
|
||||
|
||||
#################################################################################################################################
|
||||
##################### DELETE PAUSE AND RESUME MACROS IF YOU WANT TO USE YOUR OWN ONES!###########################################
|
||||
#################################################################################################################################
|
||||
|
||||
[gcode_macro PAUSE]
|
||||
rename_existing: BASE_PAUSE
|
||||
gcode:
|
||||
{% set sensor = printer['gcode_macro _SENSOR_VARIABLES'] %}
|
||||
{% set x = params.X|default(sensor.park_position_x) %}
|
||||
{% set y = params.Y|default(sensor.park_position_y) %}
|
||||
{% set z = params.Z|default(sensor.park_lift_z)|float %}
|
||||
{% set e = params.E|default(sensor.park_retraction) %}
|
||||
##### calculate save lift position #####
|
||||
{% set max_z = printer.toolhead.axis_maximum.z|float %}
|
||||
{% set act_z = printer.toolhead.position.z|float %}
|
||||
{% set lift_z = z|abs %}
|
||||
{% if act_z < (max_z - lift_z) %}
|
||||
{% set z_safe = lift_z %}
|
||||
{% else %}
|
||||
{% set z_safe = max_z - act_z %}
|
||||
{% endif %}
|
||||
SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=bed_restore_temp VALUE={printer.heater_bed.target}
|
||||
SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=extruder_restore_temp VALUE={printer.extruder.target}
|
||||
##### end of definitions #####
|
||||
SAVE_GCODE_STATE NAME=PAUSE_state
|
||||
BASE_PAUSE
|
||||
G91
|
||||
G1 E-{e} F2100
|
||||
G1 Z{z_safe}
|
||||
G90
|
||||
G1 X{x} Y{y} F6000
|
||||
# SET_LED LED=OrbiLED RED=1.0 GREEN=1.0 BLUE=0.0
|
||||
|
||||
[gcode_macro RESUME]
|
||||
rename_existing: BASE_RESUME
|
||||
variable_bed_restore_temp:0
|
||||
variable_extruder_restore_temp:0
|
||||
gcode:
|
||||
##### set defaults #####
|
||||
{% set sensor = printer['gcode_macro _SENSOR_VARIABLES'] %}
|
||||
M118 Restoring heaters temperature, it might take a whyle!
|
||||
M140 S{bed_restore_temp}
|
||||
TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_restore_temp}
|
||||
M104 S{extruder_restore_temp}
|
||||
TEMPERATURE_WAIT SENSOR=extruder MINIMUM={extruder_restore_temp}
|
||||
{% set e = params.E|default(sensor.park_retraction) %}
|
||||
G91
|
||||
G1 E{e} F2100
|
||||
G90
|
||||
RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1
|
||||
BASE_RESUME
|
||||
# SET_LED LED=OrbiLED RED=1.0 GREEN=1.0 BLUE=1.0
|
||||
|
||||
# config file version v2.2.04 change note
|
||||
# Commented ou the set Orbiled commands.
|
||||
|
||||
|
||||
# config file version v2.2.03 change note
|
||||
# 1 - defined user variables at the begining of the file for easier macro parameters adjustment
|
||||
# 2 - defined disable configuration of features
|
||||
# 3 - included PAUSE and RESUME macros with restoring bed and hotend temperature featres.
|
||||
|
||||
# config file version v2.2.02 change note
|
||||
# 1 - filament loading will not set hotend temperature to zero in case the hotend was already set hot before the loading / filament change procedure
|
||||
# 2 - Filament load / unload waits for hotend to reach temp not to reach stabilized temperature - faster filament loading and unloading.
|
||||
# 3 - Removed messages to screen, only console echo is present
|
||||
# 4 - Panel beep replaced by M300 / comment it out if not available on your printer
|
||||
# 5 - unload procedure changed for better filament tip forming.
|
||||
# 6 - known issue - if printer paused due to runout detection and new filament is not loaded whiting Klipper heaters timeout period (default is 10min) the heaters will be switched OFF.
|
||||
# If user loads new filament autoload with work with its default loading temperature of 230 deg C but the heaters temperature will not be restored afterwards user needs to set back heaters temperature.
|
||||
# on my printer this timeout also causes loosing of extruder position and printing can be resumed only after homing first and setting back temperatures manually.
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
Reference in New Issue
Block a user