diff --git a/Scripts/start_stop.cfg b/Scripts/start_stop.cfg
index ab6dfc6..8f711dc 100644
--- a/Scripts/start_stop.cfg
+++ b/Scripts/start_stop.cfg
@@ -57,6 +57,8 @@ gcode:
 	M117 Heating Extruder...
 	RESPOND MSG="Heating Extruder..."
 	M109 S{params.EXTRUDER_TEMP|default(printer.extruder.target, true) }
+#	M190 S{params.BED_TEMP|default(printer.heater_bed.target, true) } #возможно потребуется чтоб стол догревался
+
 	# Run the user created "AFTER_HEATING_EXTRUDER" macro.
 	_USER_START_PRINT_AFTER_HEATING_EXTRUDER
 	# Run the customizable "AFTER_HEATING_EXTRUDER" macro.
@@ -93,7 +95,8 @@ gcode:
     # Wait for extruder to reach a predefined preheat temp so an inductive probe (if present) is at a predictable temp. 
     # Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
     M104 S{min_temp}
-    TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
+    #TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
+	# выключил ожидание температуры, для теста
   {% endif %}
   {% if printer["gcode_macro RatOS"].z_tilt_enabled|lower == 'true' %}
     {% set TARGET_TEMP = printer.heater_bed.target %} 
@@ -110,13 +113,11 @@ gcode:
     {% endif %}
     Z_TILT_ADJUST horizontal_move_z=2
     RESTORE_GCODE_STATE NAME=STATE_Z_TILT
-
-    M190 S{TARGET_TEMP}
-  
     M117 Rehoming Z after Z tilt adjustment...
     RESPOND MSG="Rehoming Z after Z tilt adjustment..."
     # Home again as Z will have changed after tilt adjustment and bed heating.
     G28 Z
+    M140 S{TARGET_TEMP}
   {% endif %}
 
 	
@@ -144,9 +145,10 @@ gcode:
 			M140 S0
 		{% endif %}
 		{% if printer["gcode_macro RatOS"].touch_cart_enabled|lower == 'true' %}
+		    M109 S{min_temp}
             CARTOGRAPHER_TOUCH FUZZY = {printer["gcode_macro RatOS"].touch_cart_fuzzy}               ; Perform touch probe
         {% endif %}
-        M190 S{TARGET_TEMP}
+        M140 S{TARGET_TEMP}
 	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
 		BED_MESH_CLEAR
 		BED_MESH_PROFILE LOAD={printer["gcode_macro RatOS"].bed_mesh_profile}
diff --git a/macros_installer.sh b/macros_installer.sh
index d4bba1a..8f41907 100644
--- a/macros_installer.sh
+++ b/macros_installer.sh
@@ -56,8 +56,8 @@ install_backup() {
     echo "name: $NAME"      
     TOKEN=$(whiptail --inputbox "Please enter printer token" 10 100 3>&1 1>&2 2>&3)
     echo "TOKEN: $TOKEN"
-    #curl -fsSL get.klipperbackup.xyz | bash
-    cat << EOF > file.txt
+    curl -fsSL get.klipperbackup.xyz | bash
+    cat << EOF > ~/klipper-backup/.env #file.txt
     github_token=$TOKEN
     github_username=reijii
     github_repository=Klipper-Backups